Dwyer Instruments Distributors in India

2000-60PA-ASF Dwyer Instruments

 
Minimum Order Quantity12 Number
BrandDwyer USA
Measuring Range0-60 PA
Model Number2000-60PA-ASF
Usage/ApplicationIndustrial
Weight1 lb 2 oz (510 g),MP & HP 2 lb 2 oz (963 g)
Size4″ (101.6 mm) diameter dial face
Agency ApprovalRoHS
Process Connections1/8″ female NPT
Temperature Limits20 to 140 deg F (-6.67 to 60 deg C)

2000-60PA-ASF Dwyer Instruments Select the Magnehelic gage for high accuracy–guaranteed within 2% of full scale–and for the wide choice of 81 models available to suit your needs precisely. Using Dwyer’s simple, frictionless Magnehelic gage movement, it quickly indicates low air or non-corrosive gas pressures–either positive, negative (vacuum) or differential. The design resists shock, vibration and over-pressures. No manometer fluid to evaporate, freeze or cause toxic or leveling problems. It’s inexpensive, too. The Magnehelic gage is the industry standard to measure fan and blower pressures, filter resistance, air velocity, furnace draft, pressure drop across orifice plates, liquid levels with bubbler systems and pressures in fluid amplifier or fluidic systems. It also checks gas-air ratio controls and automatic valves, and monitors blood and respiratory pressures in medical care equipment

Product Highlights

  • Bezel provides flange for flush mounting in panel.
  • Clear plastic face is highly resistant to breakage. Provides undistorted viewing of pointer and scale.
  • Precision litho-printed scale is accurate and easy to read.
  • Red tipped pointer of heat treated
  • aluminum tubing is easy to see. It is rigidly mounted on the helix shaft.
  • Pointer stops of molded rubber prevent pointer over-travel without damage.
  • “Wishbone” assembly provides mounting for helix, helix bearings and pointer shaft.
  • Jeweled bearings are shock-resistant mounted; provide virtually friction-free motion for helix. Motion damped with high viscosity silicone fluid.
  • Zero adjustment screw is conveniently located in the plastic cover, and is accessible without removing the cover. O-ring seal provides pressure tightness.
  • Helix is precision made from an alloy of high magnetic permeability. Mounted in jeweled bearings, it turns freely, following the magnetic field to move the pointer across the scale.
  • Calibrated range spring is flat spring steel. Small amplitude of motion assures consistency and long life. It reacts to pressure on diaphragm. Live length adjustable for calibration.
  • Silicone rubber diaphragm with integrally molded O-ring is supported by front and rear plates. It is locked and sealed in position with a sealing plate and retaining ring. Diaphragm motion is restricted to prevent damage due to overpressures.
  • Die cast aluminum case is precision made and iridite-dipped to withstand 168 hour salt spray corrosion test.
  • Exterior finished in baked dark gray hammerloid. One case size is used for all standard pressure options, and for both surface and flush mounting.
 

Overpressure Protection:
Blowout plug is comprised of a rubber plug on the rear which functions as a relief valve by unseating and venting the gage interior when over pressure reaches approximately 25 PSIg (1.7 bar). To provide a free path for pressure relief, there are four spacer pads which maintain 0.023″ clearance when gage is surface mounted. Do not obstruct the gap created by these pads. The blowout plug is not used on models above 180″ of water pressure, medium or high pressure models, or on gages which require an elastomer other than silicone for the diaphragm. The blowout plug should not be used as a system overpressure control. High supply pressures may still cause the gage to fail due to over pressurization, resulting in property damage or serious injury. Good engineering practices should be utilized to prevent your system from exceeding the ratings or any component. O-ring seal for cover assures pressure integrity of case. Samarium Cobalt magnet mounted at one end of range spring rotates helix without mechanical linkages.

  • Range 0-60 Pa
  • Adjustable set flag
 

Series TDFS Thermal Dispersion Flow Switch

 
Minimum Order Quantity1 No
BrandDwyer USA
Agency ApprovalsCE
Housing Materials316 SS, 416 SS, Polycarbonate, Neoprene, And Acrylated Urethane
Enclosure RatingNEMA 4X (IP65)
Process Connection1/2″ NPT male
Electrical Connection4 conductor 22 AWG, 6′ (1.83 m) long with cable gland
Current ConsumptionAverage:93 mA, Peak: 300 mA
Power Requirement9 to 24 VDC
Response TimeApproximately 8 s
Pressure Limits300 psig (20.67 bar)
Wetted Materials316 SS, Polysulfone, and FKM
Setpoint Range0.5 to 10 ft/s (0.15 to 3.0 m/s)
Repeatability0.07 ft/s +3% of setpoint
Switching Current400 mA, derate 5 mA/ deg C above 23 deg C

Series TDFS Thermal Dispersion Flow Switch
  • OLD Modal TDFS-1-P-06 
  • NEW Modal TDFS-2-P-06

The Series TDFS2 Thermal Dispersion Flow Switch is a thermal flow switch that indicates whether the flow rate is above or below a user set flow rate. The unit incorporates two LED status indicators providing visual switch indication. The set flow rate (setpoint) is field adjustable and the unit has both NO and NC NPN outputs. See Figure 1 on catalog page for output and LED actions on change of flow

Product Applications:
  • Boiler Flow Proving
  • Hot Water Heaters
  • Chillers
  • Liquid Transfer Systems

Model – TDFS2-1-P-06
Thermal Dispersion Flow Switch, 316SS, 1/2″ NPT Process Connection, 6′ of Cable With Cable Gland.
 

TDFS-1-P-06 Thermal Dispersion Flow Switch

 
Minimum Order Quantity1 Number
BrandDwyer USA
Model Name/NumberTDFS-1-P-06
Material316 SS,416 SS,Polycarbonate,Neoprene,And Acrylated Urethane.
Agency ApprovalsCE
Switch Type1 NO NPN,1 NC NPN
Enclosure RatingNEMA 4X (IP65)
Process Connection1/2″ NPT male
Electrical Connection4 conductor 22 AWG,6′ (1.83 m) long with cable gland
Current ConsumptionAverage:93 mA,Peak: 300 mA
Switching Current400 mA,derate 5 mA/ deg C above 23 deg C
Power Requirement9 to 24 VDC
Response TimeApproximately 8 s
Pressure Limits300 psig (20.67 bar)
Typical Deadband0.1 ft/s +15% of setpoint
Repeatability0.07 ft/s +3% of setpoint
Setpoint Range0.5 to 10 ft/s (0.15 to 3.0 m/s)
Wetted Materials316 SS,Polysulfone,and FKM

TDFS-1-P-06 Thermal Dispersion Flow Switch
  • OLD Modal TDFS-1-P-06 
  • NEW Modal TDFS-2-P-06 

The Series TDFS2 Thermal Dispersion Flow Switch is a thermal flow switch that indicates whether the flow rate is above or below a user set flow rate. The unit incorporates two LED status indicators providing visual switch indication. The set flow rate (setpoint) is field adjustable and the unit has both NO and NC NPN outputs. See Figure 1 on catalog page for output and LED actions on change of flow

Product Applications:
  • Boiler Flow Proving
  • Hot Water Heaters
  • Chillers
  • Liquid Transfer Systems

Model – TDFS2-1-P-06
  • Thermal Dispersion Flow Switch, 316SS, 1/2″ NPT Process Connection, 6′ of Cable With Cable Gland.
 

Leave a Reply

Your email address will not be published. Required fields are marked *